Knowing Plumbing Basics is Crucial When Installing a Bathtub
Knowing Plumbing Basics is Crucial When Installing a Bathtub
Blog Article
We've discovered this great article involving How to Install a Bathtub down the page on the internet and figured it made sense to discuss it with you on this site.
Setting up a bath tub isn't exactly rocket science, however it does call for strong plumbing, carpentry, and occasionally, tiling abilities. Changing an old bath tub with a new one is likewise a moderately difficult project. If the old bathtub is conveniently obtainable, the task can relocate immediately; if you have to open up a wall surface to remove the old tub and also position the new bathtub, the job is a lot harder. In either situation, the task is within a home handyman's skills, although you will certainly require an assistant to move out the old bathtub and set in the new one. Make certain you have actually certified on your own for the work as well as are comfortable trying it. Rather than working with a professional to take control of a halfway-completed job, it is far better to take into consideration utilizing one prior to you begin. Opportunities are you may need a professional plumber to make tube links.
This post will certainly aid you mount a new tub in your restroom if you have actually already purchased a brand-new bathtub and do not need to alter the plan of your previous water pipes.
Your tools and also material list must make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, then the first thing you must do is separate the water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing taps can be quite troublesome due to the limited gain access to that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the faucets. Have a fabric prepared for the staying water that will come from the pipes. As soon as the supply pipelines have been removed, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from turning during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Before proceeding to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will need a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the placing opening in the bath/basin guaranteeing that the washers are in place between the faucet and the sink. Safeguard the tap in position with the manufacturer provided backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous kind ought to be connected to the faucet finishes initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Setting up the Tub
Making use of the two wooden boards under its feet, position the bathtub in the required setting. The wood boards are helpful in equally spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four little points.
The following goal is to make certain that the bath tub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bathtub up until the spirit level reads level.
To install faucets, fit all-time low of the furthest versatile faucet connector to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the supply of water and also examine all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Fill up the tub and additionally examine the overflow outlet and the normal outlet for leakages.
Finally, repair the bathroom paneling as defined in the maker's user's manual. Tiling and securing around the bathtub needs to wait until the bath tub has been utilized a minimum of once as this will settle it right into its final setting.
Getting ready for the Installment
Firstly, the sustaining structure provided with the bathroom needs to be fitted (if needed) according to the maker's instructions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps device to avoid pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you use all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bathroom fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, causing the water to penetrate the wall surface between the bathroom and the tiling, bring about issues with wetness as well as possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and also cartridges, and can securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill up the tub with water before securing, to permit the movement experienced when the tub is in use. The sealer can split relatively early if you do not take into account this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the market. It is advisable to fit the floor tiles using waterproof or water resistant adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that write-up about How to Install a Bathtub through an acquaintance on our other site. If you appreciated our blog entry plz remember to share it. Thanks a bunch for your time. Come back soon.
Clog issue? Reach out! Report this page